四旋翼倾转飞行器操纵冗余设计

建立了四旋翼倾转飞行器旋翼、机翼、机身的非线性气动模型和飞行动力学模型,并在Matlab/Simulink环境下搭建了仿真模型,根据仿真模型计算各个操纵面的操纵效率,确定了不同状态下各个通道需要用到的操纵方式,结合飞行动力学模型和操纵方式,在纵向通道上进行了全包线的配平计算,表明了操纵策略的可行性。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

直升机后缘襟翼驱动器迟滞现象仿真与抑制

直升机后缘襟翼多采用压电驱动器作为驱动元件，但是在使用过程中压电驱动器迟滞会对其振动控制性能产生不利影响，因此针对压电驱动器迟滞开展了迟滞建模与抑制研究。通过实验研究了压电驱动器在不同驱动频率下的迟滞特性，采用Bouc-Wen模型对驱动器迟滞现象进行了建模，并采用粒子群算法（PSO）辨识模型参数，与实际测量迟滞曲线进行了对比，在10~60 Hz范围内所建立的迟滞模型能够较为精确地描述压电驱动器迟滞现象。建立了基于Bouc-Wen逆模型的前馈补偿控制与PID反馈控制相结合的复合控制策略，实验结果显示该控制策略能够在10~60 Hz较宽的频率范围内有效抑制该压电驱动器迟滞现象。建立了考虑驱动器迟滞的主动控制后缘襟翼振动控制动力学模型，并对中等速度稳态前飞条件下后缘襟翼振动控制性能进行了仿真，仿真结果显示驱动器迟滞会在一定程度上削弱振动控制性能，而采用复合控制可以提高后缘襟翼旋翼振动控制性能。     

多支点柔性转子系统临界转速稳健设计方法

基于响应面法和容差模型提出了定量考虑参数变差影响的转子系统临界转速稳健设计方法。该方法利用响应面模型获得多参数、多目标之间的函数关系,并以多阶临界转速分布为约束条件、以临界转速对支承刚度变差敏感度最低为设计目标。对小涵道比涡扇发动机低压转子系统临界转速稳健设计结果表明:在考虑各支点支承刚度变差情况下,采用多参数、多目标稳健设计方法,可保证多支点柔性转子系统的临界转速特性在满足设计要求的同时,转子系统临界转速对支承刚度变差的敏感度最低,验证了该方法的有效性。      

对转压气机外伸激波对叶顶泄漏流影响

摘要:为了揭示对转压气机下游转子外伸激波对上游转子泄漏流的影响规律,针对上游转子叶顶间隙分别为0.2、0.5、0.8 mm的对转压气机开展了非定常数值模拟研究。研究发现:受下游转子外伸激波掠扫影响,上游转子尾缘附近压力面会形成弱压缩波,且随上游转子泄漏流增强而逐渐减弱;而该外伸激波在上游转子尾缘附近吸力面,会形成与型线切向相垂直的较强压缩波,且其位置基本不受叶顶间隙大小影响;外伸激波使上游转子尾缘附近吸、压力面压差增大,叶顶泄漏流增强,进而导致其损失增大;随着叶顶间隙增大,上游转子叶尖区弦长前半段压力波动的频率,由通道激波转为叶顶泄漏流主导,且呈现减小的趋势,而弦长后半段压力波动的频率主要由外伸激波主导,且基本不变。      

离心压缩机密封及空腔流动的一维/三维耦合建模研究

为了在保证数值预测精度的同时降低离心压缩机的建模复杂度,以一维密封泄漏计算替代完整的密封及空腔建模,开展了离心压缩机盖盘密封及空腔流动的源项建模方法研究。结果表明:基于源项方法的密封及空腔简化建模仅需在主流道建模基础上施加泄漏质量流量、总温和摩擦损失源项边界条件,即可较高精度地还原完整的盖盘密封及空腔建模的性能和关键流动细节。与完整建模相比,在全工况下源项建模预测的等熵效率的绝对偏差小于0.65%,总压比和等熵效率的相对性能偏差小于1%。该方法可在满足下游部件匹配设计精度需求的同时,减少50%以上的网格数量,并显著提高计算的经济性和收敛性。泄漏流量的计算精确度是影响源项建模法性能预测准确性的最关键因素,耦合建模可以采用一维计算中推荐的密封泄漏系数值。      

Investigation on nonlinear lateral-torsional coupled vibration of a rotor system with substantial unbalance

Substantial unbalance may be caused by fan blade off during the operation period of gas turbine engines, and related dynamic problems are very critical to the safety design of rotor system in aero-engine. This article aims to understand lateral-torsional coupled vibration of the rotor system with substantial unbalance. The governing equation of a modified unbalanced rotor system is established based on Lagrangian approach. Then, a mathematical analytical method is proposed in which a linear approximation is derived and the Floquet theory and Hill’s method are incorporated, from which the modal characteristics of the unbalanced rotor are obtained. The modal characteristics of the unbalanced rotor system are revealed comprehensively for the first time. Furthermore, the relation between the modes and responses of the unbalanced rotor is discussed in detail. The results show that the lateral vibration and torsional vibration of the unbalanced rotor are coupled through the inertial terms in the governing equations. Due to the coupling, veering and lock-in phenomena occur between the frequencies of the forward whirl mode and the torsional mode. Furthermore, lock-in can lead to a kind of principal instability. With regard to the response of the unbalanced rotor, both natural vibration components and enforced vibration components appear in the lateral response, while only natural vibration components appear during torsional vibration. Moreover, natural vibration components play a crucial role in the response within the principal instability region and cause divergence of the vibration amplitudes in the lateral and torsional directions.     

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

扩压叶栅叶尖非定常流动的涡动力学机理

为了揭示压气机叶尖区旋涡结构与流动非定常性之间的关联，采用URANS对一亚声速平面扩压叶栅在不同攻角下的流场进行了求解，并借助Q判据提取了叶尖瞬态涡系结构。结果表明：泄漏涡的破碎现象能够通过诱导新的涡结构间接作用于相邻通道的叶尖流动，是导致叶尖流场失稳的关键因素。在-0.3°和+0.7°攻角下，叶尖泄漏涡发生了螺旋破碎，并伴随有非定常诱导涡的出现，诱导涡对相邻叶片载荷的影响使得叶尖泄漏涡发生周期性摆动；在+1.7°攻角下，泄漏涡破碎会导致反流涡的形成，反流涡的输运会给叶片载荷和来流攻角带来非定常扰动，反过来又会作用于泄漏涡的破碎和反流涡的生成，最终表现为一种自维持的非定常流动现象。     

基于合成射流的旋翼翼型动态失速控制研究

针对直升机旋翼工作环境下来流速度和迎角(Angle of attack,AoA)耦合引起的动态失速问题,建立了基于合成射流的旋翼动态失速控制的数值模拟方法。采用运动嵌套网格方法,通过对翼型的平移和旋转实现变来流速度-变迎角的耦合。以积分形式的雷诺平均N-S方程为主控方程,空间离散使用Roe格式,时间离散为隐式LU-SGS方法,以OA209翼型为研究对象,在翼型上表面放置合成射流激振器,开展了射流位置、动量系数、无量纲频率以及偏角等参数对轻度失速、深度失速下翼型动态失速控制的研究。研究发现,轻度失速下,射流位置靠近气流分离点时(20%c附近,c为翼型弦长),对逆压梯度引起的轻度失速控制效果最佳。深度失速下气流分离点虽在5%c之前,但射流位于前缘分离泡后端(10%c附近)时控制效果较好。大迎角需要较大的动量系数才能有效控制。射流频率对涡结构的尺寸和数量会产生一定影响,能改变气动特性波动幅度。较小的射流偏角对轻度失速的控制更有效,而深度失速则需要较大的偏角。